South African Class 17E

South African Class 17E

Class 17E no. E1826 at Capital Park, Pretoria, Gauteng, 28 September 2006
Type and origin
Power type Electric
Designer Union Carriage & Wagon
Builder Union Carriage & Wagon
Model UCW 6E1
Build date 1977-1982
Total produced 139
Rebuilder Transnet Rail Engineering
Rebuild date 2002-2007
Number rebuilt 136 to Class 18E, Series 1
Specifications
AAR wheel arr. B-B
UIC class Bo'Bo'
Gauge 3 ft 6 in (1,067 mm) Cape gauge
Wheel diameter 1,220 mm (48.0 in)
Wheelbase 11,279 mm (37 ft 0.1 in)
  Bogie 3,430 mm (11 ft 3.0 in)
Pivot centres 7,849 mm (25 ft 9.0 in)
Panto shoes 6,972 mm (22 ft 10.5 in)
Length:
  Over couplers 15,494 mm (50 ft 10.0 in)
  Body 14,631 mm (48 ft 0 in)
Width 2,896 mm (9 ft 6.0 in)
Height:
  Pantograph 4,089 mm (13 ft 5.0 in)
  Body height 3,937 mm (12 ft 11.0 in)
Axle load 22,226 kg (49,000 lb)
Adhesive weight 88,904 kg (196,000 lb)
Loco weight 88,904 kg (196,000 lb)
Power supply Catenary
Current collection Pantographs
Traction motors Four AEI-283AY
  Rating 1 hour 623 kW (835 hp)
  Continuous 563 kW (755 hp)
Gear ratio 18:67
Loco brake Air & Regenerative
Train brakes Air & Vacuum
Couplers AAR knuckle
Performance figures
Maximum speed 113 km/h (70 mph)
Power output:
  1 hour 2,492 kW (3,342 hp)
  Continuous 2,252 kW (3,020 hp)
Tractive effort:
  Starting 311 kN (70,000 lbf)
  1 hour 221 kN (50,000 lbf)
  Continuous 193 kN (43,000 lbf) @ 40 km/h (25 mph)
Career
Operators Spoornet
Class Class 17E
Power class 3 kV DC
Number in class 139
Numbers See the table
First run 1993
Last run 2007

The Spoornet Class 17E of 1993 was a South African electric locomotive.

During 1993 and 1994, Spoornet modified several Class 6E1, Series 7, 8 and 9 locomotives to improve their braking and traction reliability for service on the Natal mainline. These modified locomotives were reclassified to Class 17E.[1]

Manufacturer

The 3 kV DC Class 6E1 electric locomotive was built for the South African Railways (SAR) by Union Carriage & Wagon (UCW) in Nigel, Transvaal, with the electrical equipment supplied by the General Electric Company (GEC). UCW did not allocate works numbers to the locomotives which it built for the SAR, but used the SAR unit numbers for their record keeping.[2]

Characteristics

Bogies

Class 6E1 Series 2 to 11 bogies

The Class 6E1 was built with sophisticated traction linkages on their bogies. Together with the locomotive's electronic wheel-slip detection system, these traction struts, mounted between the linkages on the bogies and the locomotive body and colloquially referred to as grasshopper legs, ensure the maximum transfer of power to the rails without causing wheel-slip, by reducing the adhesion of the leading bogie and increasing that of the trailing bogie by as much as 15% upon starting. This feature is controlled by electronic wheel-slip detection devices and an electric weight transfer relay, which reduce the anchor current to the leading bogie by as much as 50A in notches 2 to 16.[3]

Brakes

The locomotive itself used air brakes, but it was equipped to operate trains with air or vacuum brakes. While hauling a vacuum braked train, the locomotive's air brake system would be disabled and the train would be controlled by using the train brakes alone to slow down and stop. While hauling an air braked train, on the other hand, the locomotive brakes would engage along with the train brakes. While working either type of train downgrade, the locomotive's regenerative braking system would also work in conjunction with the train brakes.[4]

When the locomotive was stopped, the air brakes on both bogies were applied together. The handbrake or parking brake, located in cab no. 2, only operated on the unit's last axle, or no. 7 and 8 wheels.[4]

Orientation

These dual cab locomotives have a roof access ladder on one side only, just to the right of the cab access door. The roof access ladder end is marked as the no. 2 end. A corridor along the centre of the locomotive connects the cabs, which are identical, apart from the fact that the handbrake is located in cab 2. A pantograph hook stick is stowed in a tube, mounted below the lower edge of the locomotive body on the roof access ladder side.[5]

Modification to Class 17E

Class 17E locomotives were modified and reclassified from Class 6E1, Series 7, 8 or 9 locomotives during 1993 and 1994. Key modifications included improved regenerative braking and wheel-slip control to improve their reliability on the steep grades and curves of the KwaZulu-Natal mainline.[1]

A stumbling block was that the regeneration equipment at many of the sub-stations along the route was unreliable, and since there was no guarantee that another train would be in the same section to absorb the regenerated energy, there was always the risk that line voltage could exceed 4.1 kV, which would make either the sub-station or the locomotive trip out. As a result, the subsequent rebuilt Class 18E locomotives were not equipped with regenerative braking.[6]

Unlike the Class 16E locomotives, which were renumbered and reclassified but otherwise unmodified semi-permanently coupled pairs of Class 6E1, Series 3 to Series 9 locomotives, which merely had their no. 1 end cabs abandoned in terms of maintenance, the Class 17Es retained their original unit numbers after reclassification, but with a "17E" marking applied below the locomotive's unit number behind the driver's side window.[1]

Apart from the "17E" markings, they are visually indistinguishable from unmodified Class 6E1s. Those in SAR Gulf Red and yellow whiskers livery which still carried number plates, even still showed "6E1" on the plates. Altogether 139 Class 6E1 locomotives were modified to Class 17E, of which 14 were Series 7, 55 Series 8 and 70 Series 9.[1]

Rebuilding to Class 18E

Cab 1 of Class 18E no. 18-328, ex Class 17E no. E2071, Sentrarand, 22 September 2009

In 2000, Spoornet began a project to rebuild Series 2 to 11 Class 6E1 locomotives to Class 18E, Series 1 and Series 2 at the Transnet Rail Engineering (TRE) workshops at Koedoespoort. In the process, the cab at the no. 1 end was stripped of all controls and the driver's front and side windows were blanked off to have a toilet installed, thereby forfeiting the locomotive's bi-directional ability.[1][7]

Brake rack in Class 18E no. 18-089

Since the driving cab's noise level had to be below 85 decibels, cab 2 was selected as the Class 18E driving cab, primarily based on its lower noise level compared to cab 1, which is closer and more exposed to the compressor's noise and vibration. Another factor was the closer proximity of cab 2 to the low voltage switch panel. The fact that the handbrake was located in cab 2, was not a deciding factor, but was considered an additional benefit.[7]

While the earlier Class 6E1, Series 2 to 7 locomotives had been built with a brake system which consisted of various valves, connected to each other with pipes and commonly referred to as a "bicycle frame" brake system, the Class 6E1, Series 8 to 11 locomotives were built with an air equipment frame brake system, commonly referred to as a brake rack. Since the design of the rebuilt Class 18E locomotives included the same brake rack, the rebuilding project was begun with the newer series 8 to 11 locomotives to reduce the overall cost of rebuilding. [7]

Between 2002 and 2007, all but three of the Class 17Es were rebuilt to Class 18E, Series 1. The exceptions are numbers E1778, E1803 and E2035, which are presumed to have been scrapped. The table lists their Class 6E1 series and numbers, Class 18E numbers and year of rebuilding.

Illustration

The main picture shows Class 17E no. E1826, ex Class 6E1, Series 7, at Capital Park in Pretoria on 28 September 2006. The "17E" markings below the locomotive numbers on this and the following picture were the only means to visually distinguish Class 17E locomotives from unmodified Class 6E1 locomotives.

References

  1. 1 2 3 4 5 Middleton, John N. (2002). Railways of Southern Africa Locomotive Guide - 2002 (as amended by Combined Amendment List 4, January 2009) (2nd, Dec 2002 ed.). Herts, England: Beyer-Garratt Publications. pp. 49–51, 57.
  2. "UCW - Electric locomotives" (PDF). The UCW Partnership. Archived from the original (PDF) on 12 October 2007. Retrieved 30 September 2010.
  3. Paxton, Leith; Bourne, David (1985). Locomotives of the South African Railways (1st ed.). Cape Town: Struik. pp. 128–129. ISBN 0869772112.
  4. 1 2 Operation - South African Classes 6E, 6E1, 16E, 17E and 18E
  5. South African Railways Index and Diagrams Electric and Diesel Locomotives, 610mm and 1065mm Gauges, Ref LXD 14/1/100/20, 28 January 1975, as amended
  6. Class 17E braking systems
  7. 1 2 3 Information gathered from the rebuild files of individual locomotives at Transnet Rail Engineering's Koedoespoort shops, or obtained from John Middleton as well as several Transnet employees
Wikimedia Commons has media related to South African Class 17E and Class 18E rebuilt from Class 17E.
This article is issued from Wikipedia - version of the 9/13/2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.