NACA airfoil

Profile geometry – 1: Zero lift line; 2: Leading edge; 3: Nose circle; 4: Camber; 5: Max. thickness; 6: Upper surface; 7: Trailing edge; 8: Camber mean-line; 9: Lower surface
Profile lines – 1: Chord, 2: Camber, 3: Length, 4: Midline
A: blue line = chord, green line = camber mean-line, B: leading edge radius, C: x-y-coordinates for the profile geometry (Chord = x-Axis; y-Axis line on that leading edge)

The NACA airfoils are airfoil shapes for aircraft wings developed by the National Advisory Committee for Aeronautics (NACA). The shape of the NACA airfoils is described using a series of digits following the word "NACA". The parameters in the numerical code can be entered into equations to precisely generate the cross-section of the airfoil and calculate its properties.

Four-digit series

The NACA four-digit wing sections define the profile by:[1]

For example, the NACA 2412 airfoil has a maximum camber of 2% located 40% (0.4 chords) from the leading edge with a maximum thickness of 12% of the chord. Four-digit series airfoils by default have maximum thickness at 30% of the chord (0.3 chords) from the leading edge.

The NACA 0015 airfoil is symmetrical, the 00 indicating that it has no camber. The 15 indicates that the airfoil has a 15% thickness to chord length ratio: it is 15% as thick as it is long.

Equation for a symmetrical 4-digit NACA airfoil

Plot of a NACA 0015 foil, generated from formula

The formula for the shape of a NACA 00xx foil, with "xx" being replaced by the percentage of thickness to chord, is:[2]

[3][4]

where:

This equation gives the thickness as percentage of the chord length, to get the thickness the above equation should be multiplied with c.

Note that in this equation, at (x/c) = 1 (the trailing edge of the airfoil), the thickness is not quite zero. If a zero-thickness trailing edge is required, for example for computational work, one of the coefficients should be modified such that they sum to zero. Modifying the last coefficient (i.e. to −0.1036) will result in the smallest change to the overall shape of the airfoil. The leading edge approximates a cylinder with a radius of:

[5]

Now the coordinates of the upper airfoil surface, and of the lower airfoil surface are:

Equation for a cambered 4-digit NACA airfoil

Plot of a NACA 2412 foil. The camber line is shown in red, and the thickness – or the symmetrical airfoil 0012 – is shown in purple.

The simplest asymmetric foils are the NACA 4-digit series foils, which use the same formula as that used to generate the 00xx symmetric foils, but with the line of mean camber bent. The formula used to calculate the mean camber line is:[2]

where:

For this cambered airfoil, because the thickness needs to be applied perpendicular to the camber line, the coordinates and , of respectively the upper and lower airfoil surface, become:[6]

where

Five-digit series

The NACA five-digit series describes more complex airfoil shapes:[7]

For example, the NACA 23112 profile describes an airfoil with design lift coefficient of 0.3 (0.15*2), the point of maximum camber located at 15% chord (5*3), reflex camber (1), and maximum thickness of 12% of chord length (12).

The camber-line is defined in two sections:[8]

where the chordwise location and the ordinate have been normalized by the chord. The constant is chosen so that the maximum camber occurs at ; for example, for the 230 camber-line, and . Finally, constant is determined to give the desired lift coefficient. For a 230 camber-line profile (the first 3 numbers in the 5 digit series), is used.

Camber line profiles

3 digit camber lines

3 digit camber lines provide a very far forward location for the maximum camber.

The first digit is 2/3 of the design lift coefficient (in 10ths).

The second digit is twice the longitudinal location of the maximum camber location (in 10ths).

The third digit indicates a non-reflexed (0) or reflexed (1) trailing edge.

Non-Reflexed

The camber line is defined as:


The following table presents the various camber line profile coefficients:

Camber Line Profile
210 0.05 0.0580 361.40
220 0.10 0.126 51.640
230 0.15 0.2025 15.957
240 0.20 0.290 6.643
250 0.25 0.391 3.230

Reflexed

Camber lines such as 231 makes the negative trailing edge camber of the 230 series profile to be positively cambered. This results in a theoretical pitching moment of 0.

from

from

The following table presents the various camber line profile coefficients:

Camber Line Profile
221 0.10 0.130 51.990 0.000764
231 0.15 0.217 15.793 0.00677
241 0.20 0.318 6.520 0.0303
251 0.25 0.441 3.191 0.1355

Modifications

Four- and five-digit series airfoils can be modified with a two-digit code preceded by a hyphen in the following sequence:

  1. One digit describing the roundness of the leading edge with 0 being sharp, 6 being the same as the original airfoil, and larger values indicating a more rounded leading edge.
  2. One digit describing the distance of maximum thickness from the leading edge in tens of percent of the chord.

For example, the NACA 1234-05 is a NACA 1234 airfoil with a sharp leading edge and maximum thickness 50% of the chord (0.5 chords) from the leading edge.

In addition, for a more precise description of the airfoil all numbers can be presented as decimals.

1-series

A new approach to airfoil design pioneered in the 1930s in which the airfoil shape was mathematically derived from the desired lift characteristics. Prior to this, airfoil shapes were first created and then had their characteristics measured in a wind tunnel. The 1-series airfoils are described by five digits in the following sequence:

  1. The number "1" indicating the series
  2. One digit describing the distance of the minimum pressure area in tens of percent of chord.
  3. A hyphen.
  4. One digit describing the lift coefficient in tenths.
  5. Two digits describing the maximum thickness in percent of chord.

For example, the NACA 16-123 airfoil has minimum pressure 60% of the chord back with a lift coefficient of 0.1 and maximum thickness of 23% of the chord.

6-series

An improvement over 1-series airfoils with emphasis on maximizing laminar flow. The airfoil is described using six digits in the following sequence:

For example, the NACA 612-315 a=0.5 has the area of minimum pressure 10% of the chord back, maintains low drag 0.2 above and below the lift coefficient of 0.3, has a maximum thickness of 15% of the chord, and maintains laminar flow over 50% of the chord.

7-series

Further advancement in maximizing laminar flow achieved by separately identifying the low pressure zones on upper and lower surfaces of the airfoil. The airfoil is described by seven digits in the following sequence:

  1. The number "7" indicating the series.
  2. One digit describing the distance of the minimum pressure area on the upper surface in tens of percent of chord.
  3. One digit describing the distance of the minimum pressure area on the lower surface in tens of percent of chord.
  4. One letter referring to a standard profile from the earlier NACA series.
  5. One digit describing the lift coefficient in tenths.
  6. Two digits describing the maximum thickness as percent of chord.
  7. "a=" followed by a decimal number describing the fraction of chord over which laminar flow is maintained. a=1 is the default if no value is given.

For example, the NACA 712A315 has the area of minimum pressure 10% of the chord back on the upper surface and 20% of the chord back on the lower surface, uses the standard "A" profile, has a lift coefficient of 0.3, and has a maximum thickness of 15% of the chord.

8-series

Supercritical airfoils designed to independently maximize airflow above and below the wing. The numbering is identical to the 7-series airfoils except that the sequence begins with an "8" to identify the series.

See also

References

  1. E.N. Jacobs, K.E. Ward, & R.M. Pinkerton. NACA Report No. 460, "The characteristics of 78 related airfoil sections from tests in the variable-density wind tunnel". NACA, 1933.
  2. 1 2 Moran, Jack (2003). An introduction to theoretical and computational aerodynamics. Dover. p. 7. ISBN 0-486-42879-6.
  3. Aerospaceweb.org | Ask Us - NACA Airfoil Series
  4. http://www.fges.demon.co.uk/cfd/naca.html#07 Archived April 27, 2009, at the Wayback Machine.
  5. Gordon J. Leishman. Principles of Helicopter Aerodynamics. p. 361.
  6. Marzocca, Pier. "The NACA airfoil series" (PDF). Clarkson University. Retrieved July 5, 2016.
  7. E. N. Jacobs & R. M. Pinkerton 1936 Test in the variable-density wind tunnel of related airfoils having the maximum camber unusually far forward, NACA Report No. 537.
  8. Abbott, Ira (1959). Theory of Wing Sections: Including a Summary of Airfoil Data. New York: Dover Publications. p. 115. ISBN 978-0486605869.

External links

Wikimedia Commons has media related to
NACA 4-digit Airfoils
.
This article is issued from Wikipedia - version of the 12/2/2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.