Torsion bar suspension

A torsion bar with no load applied.
A torsion bar with a load applied.
A front VW Beetle suspension cross-section

A torsion bar suspension, also known as a torsion spring suspension (but not to be confused with torsion beam rear suspension), is a general term for any vehicle suspension that uses a torsion bar as its main weight bearing spring. One end of a long metal bar is attached firmly to the vehicle chassis; the opposite end terminates in a lever, the torsion key, mounted perpendicular to the bar, that is attached to a suspension arm, a spindle, or the axle. Vertical motion of the wheel causes the bar to twist around its axis and is resisted by the bar's torsion resistance. The effective spring rate of the bar is determined by its length, cross section, shape, material, and manufacturing process.

Usage

Torsion bar suspensions are used on combat vehicles or tanks like the T-72, Leopard 1, Leopard 2, M18 Hellcat, and the M1 Abrams (many tanks from World War II used this suspension), and on trucks and SUVs from Ford, Chrysler, GM, Mitsubishi, Mazda, Nissan, Isuzu and Toyota. Manufacturers change the torsion bar or key to adjust the ride height, usually to compensate for heavier or lighter engines. While the ride height may be adjusted by turning the adjuster bolts on the stock torsion key, rotating the stock key too far can bend the adjusting bolt and (more importantly) place the shock piston outside its standard travel. Over-rotating the torsion bars can also cause the suspension to hit the bump-stop prematurely, causing a harsh ride. Aftermarket forged-metal torsion key kits use relocked adjuster keys to prevent over-rotation, and shock brackets to keep the piston travel in the stock range.

Advantages and disadvantages

The main advantages of a torsion bar suspension are durability, easy adjustability of ride height, and small profile along the width of the vehicle. It takes up less of the vehicle's interior volume than coil springs.

Torsion bars reached the height of their popularity on mass-production road cars in the middle of the 20th century at the same time that unitary construction was being adopted. At a time when the mechanics of stress and metal fatigue in monocoque body frames was relatively poorly understood, torsion bars were very attractive to vehicle designers—the bars could be mounted to reinforce parts of the central structure, typically the bulkhead. Using MacPherson struts to achieve independent front suspension with coil springs meant providing strong turrets in the frontal structure of the car.

A disadvantage is that torsion bars, unlike coil springs, usually cannot provide a progressive spring rate. In most torsion bar systems, ride height (and therefore many handling features) may be changed by simply adjusting bolts that connect the torsion bars to the steering knuckles. In most cars with this type of suspension, swapping torsion bars for a different spring rate is usually an easy task.

Leveling

Some vehicles use torsion bars to provide automatic levelling, using a motor to pre-stress the bars to provide greater resistance to load and, in some cases (depending on the speed with which the motors can act), to respond to changes in road conditions. Height adjustable suspension has been used to implement a wheel-change mode where the vehicle is raised on three wheels so that the remaining wheel is lifted off the ground without the aid of a jack.

History

Before World War II, the front wheel drive Citroen Traction Avant (1934) had independent front torsion bar suspension and a flexible trailing dead axle, also sprung by torsion bars. The flexibility of the axle beam provided wheel location features like a twist beam axle.[1] The Czechoslovakian Tatra cars designed by Professor Hans Ledwinka in the mid-1930s used all round independent torsion bar suspension, along with air cooled rear engines. Also in the 1930s, prototypes of the first Volkswagen Beetle incorporated torsion bars—especially its transverse mounting style. Ledwinka's concept had been copied by Ferdinand Porsche, whose successors later had to acknowledge the influence of Ledwinka's sophisticated Tatra models on the Porsche-designed Kdf-Wagen of 1938 (later renamed the VW Beetle), a post-war lawsuit resulting in a DM3,000,000 settlement paid by Volkswagen to Ringhoffer-Tatra in 1961.

The system was applied to many new combat vehicle designs during the Second World War. It was used extensively in European cars Renault, Citroën and Volkswagen, as well as by Packard in the 1950s. The Packard used torsion bars at both front and rear, and interconnected the front and rear systems to improve ride quality. Morris Minor and Oxford from the late 1940s onwards used a front torsion bar system very similar to the Citroen, as did the Riley RM models. The then revolutionary Jaguar E-Type introduced in 1961 had a torsion bar front suspension very similar to the Citroen or Morris Minor, and an independent coil spring rear suspension using four shock absorbers with concentric springs.

An early application of a torsion bar in an American car was by Hudson Motor Car Company of Detroit who had introduced the innovative front Axle Flex suspension in 1934 Hudson and Terraplane cars and realized for 1935 that a transverse torsion bar linked to the rear axle was needed as an anti-roll bar to stabilize the cars. The single torsion bar was mounted through the frame sides behind the rear axle and then attached by arms and links to the front side of the spring U-bolt plates. Axle Flex was discontinued for the 1936 model year.

Post-war the use of torsion bar front suspension was a defining feature of British Morris cars, starting with the Morris Minor of 1948, its larger Morris Oxford MO counterpart and the upmarket Morris Six MS, plus the Wolseley-badged upmarket variants of the latter two models. The designer of these cars, Alec Issigonis was inspired by the Traction Avant's suspension although the Morris cars were rear-wheel drive and used conventional leaf springs for their rear axles. The Minor used lever arm dampers with its torsion bars while the Oxford and the Six used innovative telescopic dampers. The Minor remained in production largely unchanged until 1972 and was replaced by the Morris Marina which also used the torsion bar/lever arm damper system for its front suspension—one of the last new cars worldwide to be introduced with the system and which remained in production until 1984. The Oxford/Six platform was developed through several revised series which used Issigonis' torsion bar system until 1959 when the new 'Farina' Oxford was introduced using front suspension with coil springs, lower wishbones and lever arm dampers.

The most famous American passenger car application was the Chrysler system used beginning with the 1957 model year, such as the Imperial Crown series, although Chrysler's "Torsion-Aire" suspension was only for the front; the same basic system (longitudinal mounting) was maintained until the 1981 introduction of the K-car. A reengineered torsion bar suspension, introduced with the 1976 Dodge Aspen, introduced transverse-mounted torsion bars (possibly based on the Volkswagen Type 3 passenger car) until production ended in 1989 (with Chrysler's M platform). Some generations of the Dodge Dakota and Durango did use torsion bars on the front suspension.

General Motors first used torsion bars on their light duty pickup trucks in 1960 until it was phased out in 1963 where traditional coil springs are used up front for their 2WD trucks. Its first use in a passenger car was in 1966, starting with the E-platform vehicles (Oldsmobile Toronado, Cadillac Eldorado), 4 wheel drive S-10 pickups & Astro vans with optional all-wheel drive, and since 1988, full size trucks and SUVs with four wheel drive (GMT400, GMT800, and GMT900 series).

Porsche used torsion bar suspension for their 911 series from 1963 until 1989 with the introduction of the 964. They are also used in the rear suspension of the 924, 944, and 968.

Variations

The German World War II Panther tank (and at least some Tigers) had double torsion bars.[2] Needing bars longer than the width of the tank to get the required spring rate and maximum elastic bend angle from available steel alloys, designer Professor Ernst Lehr created a suspension that effectively folded the bars in half. For each wheel, one rod was attached to the suspension arm, while another was mounted to a nearby point on the frame. On the opposite side of the tank, the two rods were attached to each other and fitted into a pivot.[2] Deflection of the suspension arm caused both halves of the double torsion bar to twist.

Many contemporary main battle tanks use torsion bar suspension, including the American M1 Abrams,[3] German Leopard 2,[4] and Chinese MBT-3000,[5] though the newest generation of tanks such as the Russian T-14 Armata utilize an adjustable hydraulic suspension.[6] Due to their small size, tremendous load capacity, and relative ease of service, torsion bar suspension has been ideal for tanks, though it is not without disadvantage. The large travel and high elasticity of the torsion bars results in a "rocking" motion when coming to a sudden stop, making the tank's reason for existing, the gun, useless until the rocking has settled enough for the gunner to acquire the target. The motion can be compensated for with a gun stabilizer.The rocking motion can also cause crew fatigue on long marches over rough terrain. Due to the massive weight of a main battle tank, compared to an automobile, there is a much greater risk of breaking a torsion bar on sudden bumps or maneuvers, and if it is not replaced in short order the reduced suspension can affect the maneuverability of the vehicle, and in extreme cases risk immobilizing the vehicle as the reduced capacity of the suspension causes additional torsion bars to break.

Some front-wheel drive automobiles use a related type of torsion beam suspension, usually called a twist beam rear suspension, in which the rear wheels are carried on trailing arms connected by a laterally mounted torsion beam, as found on the Mitsubishi Debonair. The actual springing medium for these is usually coil springs though. The torsion beam functions both as wheel locating arm and as an anti-roll bar to resist lateral motion of the wheels as the body leans in turns. Its advantages are that it is inexpensive to manufacture and install, and engages a minimum amount of interior volume, leaving more space for the carriage of passengers, cargo, and other components. Because the torsion beam acts in the lateral plane, not vertically, the twist beam axle cannot provide ride height adjustment, and it suffers, to some extent, similar car handling limitations as other beam axle suspensions. However these limitations may not be apparent on the road, because of the trend towards firmer, more sporty suspension setups with more limited wheel travel. Twist-beam rear suspensions were pioneered on the Volkswagen Golf in the early 1970s, and remain common on compact cars and minivans.

Other uses

Torsion bars were sometimes used instead of conventional coil valve springs in some older motorcycles, such as the Honda CB450, and also on the Panhard Dyna X and Panhard Dyna Z cars of the 1950s. They were also used in the door mechanism of the DeLorean DMC-12 automobile.

References

  1. Popular Mechanics - Google Books. Books.google.com. Retrieved 2015-03-03.
  2. 1 2 "Armortek • View topic - Ultimathe Panther by Luca". Armortek.co.uk. Retrieved 2015-03-03.
  3. "M1 Abrams Main Battle Tank". www.globalsecurity.org. Retrieved 2016-01-16.
  4. "Main Battle Tank - Leopard 2". www.fprado.com. Retrieved 2016-01-16.
  5. "The Chinese MBT-3000 Main Battle Tank - TankNutDave.com". TankNutDave.com. Retrieved 2016-01-16.
  6. "Gur Khan attacks!: Активная подвеска танка "Армата"". gurkhan.blogspot.ru. Retrieved 2016-01-16.

External links

This article is issued from Wikipedia - version of the 11/11/2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.