Pull-up resistor

When the switch is open the voltage of the gate input is pulled up to the level of Vin. When the switch is closed, the input voltage at the gate goes to ground.

In electronic logic circuits, a pull-up resistor is a resistor connected between a signal conductor and a positive power supply voltage to ensure that the signal will be a valid logic level if external devices are disconnected or high-impedance is introduced. They may also be used at the interface between two different types of logic devices, possibly operating at different logic levels and power supply voltages.

A pull-up resistor pulls the voltage of the signal it is connected to towards its voltage source level. When the other components associated with the signal are inactive, the voltage supplied by the pull up prevails and brings the signal up to a logical high level. When another component on the line goes active, it overrides the pull-up resistor. The pull-up resistor ensures that the wire is at a defined logic level even if no active devices are connected to it.

A pull-down resistor works in the same way but is connected to ground. It holds the logic signal at a low logic level when no other active device is connected.

Applications

A pull-up resistor may be used when interfacing logic gates to inputs. For example, an input signal may be pulled by a resistor, then a switch or jumper strap can be used to connect that input to ground. This can be used for configuration information, to select options or for troubleshooting of a device.

Pull-up resistors may be used at logic outputs where the logic device cannot source current such as open-collector TTL logic devices. Such outputs are used for driving external devices, for a wired-OR function in combinational logic, or for a simple way of driving a logic bus with multiple devices connected to it. For example, the circuit shown on the right uses 0V logic level inputs to actuate a relay. If the input is left unconnected, pull-down resistor R1 ensures that the input is pulled down to a logic low. The 7407 TTL device, an open collector buffer, simply outputs whatever it receives as input, but as an open collector device, the output is left effectively unconnected when outputting a "1". Pull-up resistor R2 thus pulls the output all the way up to 12 V when the buffer outputs a "1", providing enough voltage to turn the power MOSFET all the way on and actuate the relay.

Pull-up resistors may be discrete devices mounted on the same circuit board as the logic devices. Many microcontrollers intended for embedded control applications have internal, programmable pull-up resistors for logic inputs so that minimal external components are needed.

Some disadvantages of pull-up resistors are the extra power consumed when current is drawn through the resistor and the reduced speed of a pull-up compared to an active current source. Certain logic families are susceptible to power supply transients introduced into logic inputs through pull-up resistors, which may force the use of a separate filtered power source for the pull-ups.

Pull-down resistors can be safely used with CMOS logic gates because the inputs are voltage-controlled. TTL logic inputs that are left un-connected inherently float high, and require a much lower valued pull-down resistor to force the input low. A standard TTL input at logic "1" is normally operated assuming a source current of 40 µA, and a voltage level above 2.4 V, allowing a pull-up resistor of no more than 50 Kohms; whereas the ttl input at logic "0" will be expected to sink 1.6 mA at a voltage below 0.8 V, requiring a pull-down resistor less than 500 ohms.[1] Holding unused TTL inputs low consumes more current. For that reason, pull-up resistors are preferred in TTL circuits.

In bipolar logic families operating at 5 VDC, a typical pull-up resistor value will be 1000–5000 Ω, based on the requirement to provide the required logic level current over the full operating range of temperature and supply voltage. For CMOS and MOS logic, much higher values of resistor can be used, several thousand to a million ohms, since the required leakage current at a logic input is small.

References

  1. "Quadruple 2-input positive-NAND gates" (PDF). Texas Instruments. October 2003. Retrieved 11 August 2015.

See also

This article is issued from Wikipedia - version of the 6/11/2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.