Power cord

Not to be confused with Power chord.
Power cord, with plug at end, plugged into a Japanese outlet with ground post, for a washing machine.

A power cord, line cord, or mains cable is a cable that temporarily connects an appliance to the mains electricity supply via a wall socket or extension cord. The terms are generally used for cables using a power plug to connect to a single-phase alternating current power source at the local line voltage(generally 100 to 240 volts, depending on the location). The terms power cable, mains lead, flex or kettle lead are also used. A lamp cord (also known as a zip cord) is a light-weight, ungrounded, single-insulated two-wire cord used for small loads such as a table or floor lamp.

A cord set includes connectors molded to the cord at each end (see Appliance coupler). Cord sets are detachable from both the power supply and the electrical equipment, and consist of a flexible cord with electrical connectors at either end, one male, and one female. One end of the cord set is attached to a molded electrical plug; the other is typically a molded electrical receptacle to prevent the possibility of having an exposed live prong or pin which would cause electric shock. The female connector attaches to the piece of equipment or appliance while the male plug connects to the electrical receptacle or outlet.


Power cables may be either fixed or detachable from the appliance. In the case of detachable leads, the appliance end of the power cord has a female connector to link it to the appliance, to avoid the dangers from having a live protruding pin. Cords may also have twist-locking features, or other attachments to prevent accidental disconnection at one or both ends. A cord set may include accessories such as fuses for overcurrent protection, a pilot lamp to indicate voltage is present, or a leakage current detector. Power cords for sensitive instruments, or audio/video equipment may also include a shield over the power conductors to minimize electromagnetic interference.

A power cord or appliance coupler may have a retaining clamp, a mechanical device that prevents it from inadvertently being pulled or shaken loose. Typical application areas with stricter safety requirements include medical technology, stage and lighting technology, and computing equipment. For specialty equipment such as construction machinery, sound and lighting equipment, emergency medical defibrillators and electrical power tools, used in locations without a convenient power source, extension cords are used to carry the electric current up to hundreds of feet away from an outlet.

In North America, the National Electrical Manufacturers Association develops standards for electrical plugs and receptacles and cables.[1]

International power cords and plug adapters are used in conjunction with electrical appliances in countries different from those in which they were designed to operate. Besides a cord with one end compatible to receptacles or a device from one country and the other end compatible with receptacles or devices from another country, a voltage converter is usually necessary, as well, to protect travelers' electronic devices, such as laptops, from the differing voltages between the United States and places like Europe or Africa.

North American lamp cords have two single-insulated conductors designed for low-current applications. The insulator covering one of the conductors is ribbed (parallel to wire) for the entire length of the cord, while the other conductor's insulator is smooth. The smooth one is hot and the ribbed one is neutral.[2]


IEC 60320 power cables come in normal and high-temperature variants, as well as various rated currents. The connectors have slightly different shapes to ensure that it is not possible to substitute a cable with a lower temperature or current rating, but that it is possible to use an overrated cable. Cords also have different types of exterior jackets available to accommodate environmental variables such as moisture, temperature, oils, sunlight, flexibility, and heavy wear. For example, a heating appliance may come with a cord designed to withstand accidental contact with heated surfaces.

Worldwide, more than a dozen different types of connectors are used for fixed building wiring. Products sold in many different markets can use a standardized IEC 60320 connector and then use a detachable power cord to match the local electrical outlets. This simplifies safety approvals, factory testing, and production since the power cord is a low-cost item available as a commodity. Note that the same types of appliance-side connectors are used with both 110 V and 230 V power cables, so care must be used when moving appliances between countries with different voltage standards substituting a power cord that matches local power outlets will result in an incorrect voltage being applied to the appliance or equipment. Unless explicitly labelled as capable of handling local voltages, this is very likely to damage or destroy the appliance. Some devices have a slide-switch to adapt to different voltages, or wide-ranging power supplies.


Within the United States, the Department of Defense maintains commercial item description (CID) A-A-55815[3] for power supply cords. These cords are of the "standard" power cord style in the United States, having a NEMA 5-15P plug on one end and an IEC 60320 C13 receptacle on the other. The CID requires the cords to meet UL Standards 62[4] and 817.[5]

Power supplies

Cord sets must be distinguished from plug-in wall mounted power supplies, where the connector also contains a transformer, and possibly rectifiers, filters and regulators. Unwary substitution of a standard mains-voltage connector for the power supply would result in application of full line voltage to the connected device, resulting in its destruction and possible fire or personal injury.

See also


  1. NEMA - Flexible Cords Section
  2. Merle Henkenius; Popular Mechanics Dec 1987 How to Repair an Incandescent Lamp:Installing an in-line switch; p.130; (retrieved 3/23/12)
  3. A-A-55815 (1995-11-13). "Cable Assembly, (Type II), Electronic Test Equipment, (2 Poles, 3 Wires, Grounded, 125 Volts, 10 Amperes, 50 or 60 Hertz), Grounding Plug Connector, and Straight Molded Type II Equipment Connector". Retrieved 2013-09-22.
  4. UL 62 (2010-05-18). "Flexible Cords and Cables". Retrieved 2013-09-22.
  5. UL 817 (2001-03-16). "Standard for Cord Sets and Power-Supply Cords". Retrieved 2013-09-22.
This article is issued from Wikipedia - version of the 11/16/2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.