Photometry (astronomy)

Photometry is a technique of astronomy concerned with measuring the flux, or intensity of an astronomical object's electromagnetic radiation.[1] When photometry is performed over broad wavelength bands of radiation, where not only the amount of radiation but also its spectral distribution is measured, the term spectrophotometry is used.

The word is composed of the Greek affixes photo- ("light") and -metry ("measure").


The methods used to perform photometry depend on the wavelength regime under study. At its most basic, photometry is conducted by gathering light in a telescope, sometimes passing it through specialized photometric optical bandpass filters, and then capturing and recording the light energy with a photosensitive instrument. Standard sets of passbands (called a photometric system) are defined to allow accurate comparison of observations.[2]

Historically, photometry in the near-infrared through long-wavelength ultra-violet was done with a photoelectric photometer, an instrument that measured the light intensity of a single object by directing its light onto a photosensitive cell. These have largely been replaced with CCD cameras that can simultaneously image multiple objects, although photoelectric photometers are still used in special situations, such as where fine time resolution is required.

CCD photometry

A CCD camera is essentially a grid of photometers, simultaneously measuring and recording the photons coming from all the sources in the field of view. Because each CCD image records the photometry of multiple objects at once, various forms of photometric extraction can be performed on the recorded data; typically relative, absolute, and differential. All three will require the extraction of the raw image magnitude of the target object, and a known comparison object. The observed signal from an object will typically cover many pixels according to the point spread function (PSF) of the system. This broadening is due to both the optics in the telescope and the astronomical seeing. When obtaining photometry from a point source, the flux is measured by summing all the light recorded from the object and subtract the light due to the sky. The simplest technique, known as aperture photometry, consists of summing the pixel counts within an aperture centered on the object and subtracting the product of the nearby average sky count per pixel and the number of pixels within the aperture.[3][4] This will result in the raw flux value of the target object. When doing photometry in a very crowded field, such as a globular cluster, where the profiles of stars overlap significantly, one must use de-blending techniques, such as PSF fitting to determine the individual flux values of the overlapping sources.[5]


After determining the flux of an object in counts, the flux is normally converted into instrumental magnitude. Then, the measurement is calibrated in some way. Which calibrations are used will depend in part on what type of photometry is being done. Typically, observations are processed for relative, or differential photometry.[6] Relative photometry is the measurement of the apparent brightness of multiple objects relative to each other. Absolute photometry is the measurement of the apparent brightness of an object on a standard photometric system; these measurements can be compared with other absolute photometric measurements obtained with different telescopes or instruments. Differential photometry is the measurement of the difference in brightness of two objects. In most cases, differential photometry can be done with the highest precision, while absolute photometry is the most difficult to do with high precision. Also, accurate photometry is usually more difficult when the apparent brightness of the object is fainter.

Absolute photometry

To perform absolute photometry one must correct for differences between the effective passband through which an object is observed and the passband used to define the standard photometric system. This is often in addition to all of the other corrections discussed above. Typically this correction is done by observing the object(s) of interest through multiple filters and also observing a number of photometric standard stars. If the standard stars cannot be observed simultaneously with the target(s), this correction must be done under photometric conditions, when the sky is cloudless and the extinction is a simple function of the airmass.

Relative photometry

To perform relative photometry, one compares the instrument magnitude of the object to a known comparison object, and then corrects the measurements for spatial variations in the sensitivity of the instrument and the atmospheric extinction. This is often in addition to correcting for their temporal variations, particularly when the objects being compared are too far apart on the sky to be observed simultaneously. When doing the calibration from an image that contains both the target and comparison objects in close proximity, and using a photometric filter that matches the catalog magnitude of the comparison object most of the measurement variations decrease to null.

Differential photometry

Differential photometry is the simplest of the calibrations and most useful for time series observations. When using CCD photometry, both the target and comparison objects are observed at the same time, with the same filters, using the same instrument, and viewed through the same optical path. Most of the observational variables drop out and the differential magnitude is simply the difference between the instrument magnitude of the target object and the comparison object (∆Mag = C Mag – T Mag). This is very useful when plotting the change in magnitude over time of a target object, and is usually compiled into a light curve.


Photometric measurements can be combined with the inverse-square law to determine the luminosity of an object if its distance can be determined, or its distance if its luminosity is known. Other physical properties of an object, such as its temperature or chemical composition, may be determined via broad or narrow-band spectrophotometry. Typically photometric measurements of multiple objects obtained through two filters are plotted on a color-magnitude diagram, which for stars is the observed version of the Hertzsprung-Russell diagram. Photometry is also used to study the light variations of objects such as variable stars,[7] minor planets, active galactic nuclei and supernovae, or to detect transiting extrasolar planets. Measurements of these variations can be used, for example, to determine the orbital period and the radii of the members of an eclipsing binary star system, the rotation period of a minor planet or a star, or the total energy output of a supernova.


A number of free computer programs are available for synthetic aperture photometry and PSF-fitting photometry. SExtractor ( and Aperture Photometry Tool ( are popular examples for aperture photometry. The former is geared towards reduction of large scale galaxy-survey data, and the latter has a graphical user interface (GUI) suitable for studying individual images. DAOPHOT is recognized as the best software for PSF-fitting photometry.[5]


There are a number of organizations, from professional to amateur, that gather and share photometric data and make it available on-line. Some sites gather the data primarily as a resource for other researchers (e.x. AAVSO) and some solicit contributions of data for their own research (i.e. CBA):

See also


  1. Sterken, Christiaan; Manfroid, J. (1992), Astronomical photometry: a guide, Astrophysics and space science library, 175, Springer, pp. 1–6, ISBN 0-7923-1653-3
  2. Warner, Brian (2006). A Practical Guide to Lightcurve Photometry and Analysis, Springer, ISBN 0-3872-9365-5
  3. Mighell, Kenneth J. (1999). "Algorithms for CCD Stellar Photometry". ASP Conference Series. 172: 317–328.
  4. Laher, Russ R.; et al. (2012). "Aperture Photometry Tool". Publications of the Astronomical Society of the Pacific. 124 (917): 737–763. Bibcode:2012PASP..124..737L. doi:10.1086/666883.
  5. 1 2 Stetson, Peter B. (1987). "DAOPHOT: A Computer Program for Crowded-Field Stellar Photometry". Publications of the Astronomical Society of the Pacific. 99: 191–222. Bibcode:1987PASP...99..191S. doi:10.1086/131977.
  6. Hubbell, Gerald R. (2013). Scientific Astrophotography: How Amateurs Can Generate and Use Professional Imaging Data: 264-266. Springer, ISBN 978-1-4614-5173-0
  7. North, Gerald, (2004). Observing Variable Stars, Novae and Supernovae, Cambridge, ISBN 0-521-82047-2
This article is issued from Wikipedia - version of the 11/3/2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.