Mercedes-Benz M100 engine

Mercedes-Benz M-100 engine
Overview
Manufacturer Daimler-Benz
Production 1963-1981
Combustion chamber
Configuration V8
Displacement
  • 6,332 cc (386.4 cu in) (1963-1975)
  • 6,834 cc (417.0 cu in) (1976-1981)
Cylinder bore
  • 103 mm (4.1 in) (1963-1975)
  • 107 mm (4.2 in) (1976-1981)
Piston stroke 95 mm (3.7 in)
Cylinder block alloy Cast iron
Cylinder head alloy Aluminum
Valvetrain OHC
Compression ratio
  • 9.0:1 (1963-1975)
  • 8.8:1 (1976-1981)
Combustion
Fuel system
  • Daimler-Benz designed mechanical fuel injection (1963-1972)
  • Bosch D-Jetronic analog fuel injection (1973-1975)
  • Bosch K-Jetronic mechanical fuel injection (1976-1981)
Fuel type Gasoline
Cooling system water-cooled
Output
Power output
  • 250 PS (180 kW; 250 hp) @ 4000 (1963-1975)
  • 286 PS (210 kW; 282 hp) @ 4250 (1976-1981)
Torque output
  • 503 N·m (371 ft·lb) @ 2800 rpm (1963-1975)
  • 550 N·m (410 ft·lb) @ 3000 rpm (1976-1981)

The Mercedes-Benz M100 engine was introduced in the 1963 Mercedes-Benz 600 with 6.3 litres, and later also used in the Mercedes-Benz 300SEL 6.3 from 1968 onwards, and even larger, in the 1970s Mercedes-Benz 450SEL 6.9.

It featured a cast iron V8 with a single overhead camshaft operating sodium-filled valves (as are found in piston-driven aircraft) against hardened valve seats on each aluminium alloy cylinder head.

Each hand-built unit was bench-tested for 265 minutes, 40 of which were under full load. A mechanical fuel injection system designed and built in-house by Daimler-Benz was used until 1972, whereas the Bosch D-Jetronic electronic fuel injection was used from 1973. Several years later came a switch to K-Jetronic. As in all Mercedes-Benz automobile engines, the crankshaft, connecting rods and pistons were forged instead of cast.

In non-US trim, the 6.9 litre (6834 cc or 417 in³) power plant was conservatively rated at 286 PS (213 kW) with 405 ft·lbf (549 Nm) of torque helping to compensate for the 2.65 to 1 final drive ratio necessary for sustained high-speed cruising. The North American version, introduced in 1977, was significantly less powerful at 250 horsepower (186 kW) and 360 ft·lbf (488 N·m) of torque due to more stringent emissions control requirements. Bosch K-Jetronic electromechanical fuel injection came standars on the 450 SEL 6.9.

In the interest of both engine longevity as well as creating some extra space under the hood, a "dry sump" engine lubrication system was used. Originally developed for use in race cars as a way to prevent foaming of the engine oil by the crankshaft which in turn would create a serious drop in oil pressure, the system circulated twelve litres of oil between the storage tank mounted inside the right front fender and the engine as opposed to the usual four or five litres found in V8s with a standard oil pan and oil pump. As a result, the engine itself had no dipstick for checking the oil level. Rather, the dipstick was attached to the inside of the tank's filler cap (accessible from the engine compartment) and the oil level was checked with the engine running and at operating temperature. The dry sump system also had the benefit of extending the oil change interval to 12,500 miles (20,000 km). This, along with hydraulic valve lifters which required no adjusting and special cylinder head gaskets which eliminated the need for periodic retorquing of the head bolts, made the 6.9 nearly maintenance-free for its first 50,000 miles (80,500 km). The 6.9 required little basic service other than coolant, minor tune-ups, oil changes and replacement of the air, fuel, oil and power-steering-fluid filters.

This article is issued from Wikipedia - version of the 8/18/2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.