Enfield No. 2

Enfield No 2 Mk I Revolver
Type Service pistol
Place of origin United Kingdom
Service history
In service 1932–1963
Used by United Kingdom & Colonies, British Commonwealth,
Wars World War II, Korean War, British colonial conflicts, numerous others
Production history
Designer Royal Small Arms Factory, Webley & Scott
Designed 1928
Manufacturer RSAF Enfield
Produced 1932–1957
Number built approx 270,000
Variants Enfield No 2 Mk I*, Enfield No 2 Mk I**
Specifications
Weight 1.7 lb (765 g), unloaded
Length 10.25 in (260 mm)
Barrel length 5.03 in (127 mm)

Cartridge .380" Revolver Mk I or Mk IIz
Calibre 0.38 inch (9.65 mm)
Action Double-action revolver (Mk I* and Mk I** double action only)
Rate of fire 20–30 rounds/minute
Muzzle velocity 620 ft/s (189 m/s)
Effective firing range 15 yards (13.7 m)
Maximum firing range 200 yd
Feed system 6-round cylinder
Sights fixed front post and rear notch

The Enfield No.2 was a British top-break revolver using the .38/200 round manufactured from 1932 to 1957. It was the standard British/Commonwealth sidearm in the Second World War, alongside the Webley Mk VI and Smith & Wesson Victory Model revolvers chambered in the same calibre.

History

After the First World War, it was decided by the British Government that a smaller and lighter .38 calibre (9.2 mm) sidearm firing a long, heavy 200 grain (13 g) soft lead bullet would be preferable to the large Webley service revolvers using the .455 (11.6 mm) round.[1][2] While the .455 had proven to be an effective weapon for stopping enemy soldiers, the recoil of the .455 cartridge complicated marksmanship training.[3] The authorities began a search for a double-action revolver with less weight and recoil that could be quickly mastered by a minimally trained soldier,[4] with a good probability of hitting an enemy with the first shot at extremely close ranges.[5] By using such a long, heavy, round-nosed lead bullet in a .38 calibre cartridge, it was found that the bullet, being minimally stabilised for its weight and calibre, tended to 'keyhole' or tumble longitudinally when striking an object, theoretically increasing wounding and stopping ability of human targets at short ranges.[6][7] At the time, the .38 calibre Smith & Wesson cartridge with 200-grain (13 g) lead bullet, known as the .38/200, was also a popular cartridge in civilian and police use (in the USA, the .38/200 or 380/200 was known as the .38 Super Police load).[7] Consequently, the British firm of Webley & Scott tendered their Webley Mk IV revolver in .38/200 calibre.[8] Rather than adopting it, the British authorities took the design to the Government-run Royal Small Arms Factory at Enfield, and the Enfield factory came up with a revolver that was very similar to the Webley Mk IV .38, but internally slightly different. The Enfield-designed pistol was quickly accepted under the designation Revolver, No 2 Mk I, and was adopted in 1931,[9] followed in 1938 by the Mk I* (spurless hammer, double-action only),[10] and finally the Mk I** (simplified for wartime production) in 1942.[11]

Webley sued the British Government for £2,250, being "costs involved in the research and design" of the revolver. Their action was contested by Enfield, who stated that the Enfield No 2 Mk I was actually designed by Captain Boys (the Assistant Superintendent of Design, famous for the Boys Rifle) with assistance from Webley & Scott, and not the other way around—accordingly, their claim was denied. By way of compensation, however, the Royal Commission on Awards to Inventors awarded Webley & Scott £1,250.[12]

RSAF Enfield was unable to manufacture enough No. 2 revolvers to meet the military's wartime demands, and as a result Webley's Mk IV was also adopted as a standard sidearm for the British Army.

Variants

Enfield No.2 Mk I* revolver, used by the Tank Corps, and all other British Army soldiers equipped with pistols. The No. 2 Mk I* configuration was double-action only and is therefore missing the hammer spur that would enable it to be manually cocked by the firer.
an Enfield No. 2 Mk1 in fine condition. from bench rest at 25 yards.
One hand rapid fire group with Enfield 38/200

There were two main variants of the Enfield No 2 Mk I revolver. The first was the Mk I*, which had a spurless hammer and was double-action only, meaning that the hammer could not be thumb-cocked by the shooter for each shot. Additionally, in keeping with the revolver's purpose as a close-range weapon, the handgrips, now made of plastic, were redesigned to improve grip when used in rapid double-action fire; the new handgrip design was given the designation Mk II.[13] The majority of Enfields produced were either Mk I* or modified to that standard.[14] The second variant was the Mk I**, which was a 1942 variant of the Mk I* simplified in order to increase production, but was discontinued shortly thereafter as a result of safety concerns over some of the introduced modifications.

The vast majority of Enfield No 2 Mk I revolvers were modified to Mk I* during World War II, generally as they came in for repair or general maintenance;[10] It is believed that the reason was that the Mk I* version was cheaper and faster to manufacture and allowed for far quicker training.[15] When used in the manner in which British forces trained (rapid double-action fire at very close ranges), the No 2 Mk I* is at least as accurate as any other service pistol of its time, because of the relatively light double-action trigger pull. It is not, however, the best choice for deliberately aimed, long-distance shooting — the double-action pull will throw the most competent shooter's aim off enough to noticeably affect accuracy at ranges of more than 15 yards (14 m) or so.[2] Some unit Armourers are known to have retrofitted the Enfield No 2 Mk I* back to the Mk I variant, but this was never an official policy and appears to have been done on an individual basis. Despite officially being declared obsolete at the end of World War II, the Enfield (and Webley revolvers) were not completely phased out in favour of the Browning Hi-Power until April 1969.[16]

The Enfield No 2 is very fast to reload—as are all British top-break revolvers—because of its automatic ejector, which simultaneously removes all six cases from the cylinder. British combat experience during World War II with the .38/200 Enfield revolvers during World War II seemed to confirm that, "for the average soldier", the Enfield No. 2 Mk I could be used far more effectively than the bulkier and heavier .455 calibre Webley revolvers that had been issued during World War I.[2] Perhaps because of the relatively long double-action trigger pull compared to other pistols capable of single-action fire,[14] the double-action-only Mk I* revolvers were not popular with troops,[14] many of whom took the first available opportunity to exchange them in favour of Smith & Wesson, Colt, or Webley revolvers.[17]

Ammunition

The Enfield No.2 Mk I was designed for use with the Cartridge S.A. Ball Revolver .380 inch Mk. I and Mk.Iz, a deviation of the .38 Smith & Wesson cartridge, also known as the .38/200. It had a 200 gr (13 g). unjacketed round-nose, lead bullet of .359 inch diameter that developed a muzzle velocity of 620–650 ft/s (190–200 m/s).

Just prior to the outbreak of the Second World War, British authorities became concerned that the soft unjacketed lead bullet used in the 380/200 might be considered as violating the Hague Convention of 1899 governing deforming or 'explosive bullets'. A new .38 loading was introduced for use in combat utilizing a 178-grain (11.5 g), gilding-metal-jacketed lead bullet; new foresights were issued to compensate for the new cartridge's ballistics and change to the point of aim.[13] The new cartridge was accepted into Commonwealth Service as "Cartridge, Pistol, .380 Mk IIz", firing a 178 - 180 grain (11.7 g) full metal jacket round-nose bullet. The 380/200 Mk I lead bullet cartridge was continued in service, originally restricted to training and marksmanship practice.[13] However, after the outbreak of war, supply exigencies forced British authorities to use both the 380/200 Mk I and the .380 Mk IIz loadings interchangeably in combat. U.S. ammunition manufacturers such as Winchester-Western supplied 380/200 Mk I cartridges to British forces throughout the war.[18]

Other manufacturers

The vast majority of Enfield No 2 revolvers were made by RSAF (Royal Small Arms Factory) Enfield, but wartime necessities meant that numbers were produced elsewhere. Albion Motors in Scotland made the Enfield No 2 Mk I* from 1941 to 1943, whereupon the contract for production was passed onto Coventry Gauge & Tool Co. By 1945, 24,000[19] Enfield No 2 Mk I* and Mk I** revolvers had been produced by Albion/CG&T. The Singer Sewing Machine Company of Clydebank made components but they were assembled at Enfield under their proofmarks; Singer-made parts are marked "SSM".

The Howard Auto Cultivator Company (HAC) in New South Wales, Australia tooled up and began manufacturing the Enfield No 2 Mk I* and I** revolvers in 1941, but the production run was very limited (estimated at around 350 or so revolvers in total), and the revolvers produced were criticised for being non-interchangeable, even with other HAC-produced revolvers. Very few HAC revolvers are known to exist, and it is thought by many collectors that most of the HAC revolvers may have been destroyed in the various Australian Gun Amnesties and "Buy-Backs".

Users

See also

Notes

  1. Stamps, Mark, and Ian Skennerton, .380 Enfield Revolver No. 2, page 9.
  2. 1 2 3 Smith, W.H.B, 1943 Basic Manual of Military Small Arms (facsimile), page 11.
  3. Shore, C. (Capt), With British Snipers to the Reich, Paladin Press (1988), pp. 200-201
  4. Weeks, John, World War II Small Arms, London: Orbis Publishing Ltd. (1979), p. 76: "the standard pistol training ammunition allocation per soldier was only 12 rounds per year"
  5. Shore, C. (Capt), With British Snipers to the Reich, Paladin Press (1988), p. 201
  6. Shore, (1988) p. 202
  7. 1 2 Barnes, Frank C., Cartridges of the World, 6th ed. DBI Books (1989), p. 239
  8. Maze, Robert J., Howdah to High Power, page 103.
  9. § A6862, LoC
  10. 1 2 § B2289, LoC
  11. § B6712, LoC
  12. Stamps, Mark, and Ian Skennerton, .380 Enfield Revolver No. 2, page 12.
  13. 1 2 3 Dunlap, Roy, Ordnance Went Up Front, Samworth Press (1948), p. 141
  14. 1 2 3 Weeks, John, World War II Small Arms, London: Orbis Publishing Ltd. (1979), p. 76
  15. Wilson, Royce, "A Tale of Two Collectables", Australian Shooter magazine, March 2006.
  16. Stamps, Mark, and Ian Skennerton, .380 Enfield Revolver No. 2, page 118
  17. Stamps, Mark, and Ian Skennerton, .380 Enfield Revolver No. 2, page 79
  18. Shore, C. (Capt.), With British Snipers to the Reich, Paladin Press (1989), p. 201
  19. Hogg, Ian V., and John Walter.Pistols of the World, 4th Ed.
  20. 1 2 Hogg, Ian (1989). Jane's Infantry Weapons 1989-90, 15th Edition. Jane's Information Group. p. 831. ISBN 0-7106-0889-6.

References

Wikimedia Commons has media related to Enfield No.2.
This article is issued from Wikipedia - version of the 11/25/2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.