For other uses, see Chirp (disambiguation).

A chirp is a signal in which the frequency increases (up-chirp) or decreases (down-chirp) with time. In some sources, the term chirp is used interchangeably with sweep signal.[1] It is commonly used in sonar and radar, but has other applications, such as in spread-spectrum communications. In spread-spectrum usage, surface acoustic wave (SAW) devices such as reflective array compressors (RACs) are often used to generate and demodulate the chirped signals. In optics, ultrashort laser pulses also exhibit chirp, which, in optical transmission systems, interacts with the dispersion properties of the materials, increasing or decreasing total pulse dispersion as the signal propagates. The name is a reference to the chirping sound made by birds; see bird vocalization.


If a waveform is defined as:

then the instantaneous frequency is defined to be the phase rate:

and the (instantaneous) chirpyness is defined to be the frequency rate:[lower-alpha 1]



A linear chirp waveform; a sinusoidal wave that increases in frequency linearly over time
Spectrogram of a linear chirp. The spectrogram plot demonstrates the linear rate of change in frequency as a function of time, in this case from 0 to 7 kHz, repeating every 2.3 seconds. The intensity of the plot is proportional to the energy content in the signal at the indicated frequency and time.
Linear chirp
Sound example for linear chirp (five repetitions)

Problems playing this file? See media help.

In a linear chirp, the instantaneous frequency varies exactly linearly with time:


where is the starting frequency (at time ), and is the rate of frequency change or chirpyness.


where is the final frequency and is the starting frequency. is the time it takes to sweep from to .

The corresponding time-domain function for the phase of any oscillating signal is the integral of the frequency function, since one expects the phase to grow like , i.e., that the derivative of the phase is the angular frequency .

For the linear chirp, this results in:

where is the initial phase (at time ). Thus this is also called quadratic-phase signal.[3]

The corresponding time-domain function for a sinusoidal linear chirp is the sine of the phase in radians:


An exponential chirp waveform; a sinusoidal wave that increases in frequency exponentially over time
Spectrogram of an exponential chirp. The exponential rate of change of frequency is shown as a function of time, in this case from nearly 0 up to 8 kHz repeating every second. Also visible in this spectrogram is a frequency fallback to 6 kHz after peaking, likely an artifact of the specific method employed to generate the waveform.
Exponential chirp
Sound example for exponential chirp (five repetitions)

Problems playing this file? See media help.

In a geometric chirp, also called an exponential chirp, the frequency of the signal varies with a geometric relationship over time. In other words, if two points in the waveform are chosen, and , and the time interval between them is kept constant, the frequency ratio will also be constant.

In an exponential chirp, the frequency of the signal varies exponentially as a function of time:

where is the starting frequency (at ), and is the rate of exponential change in frequency. Unlike the linear chirp, which has a constant chirpyness, an exponential chirp has an exponentially increasing frequency rate.

The corresponding time-domain function for the phase of an exponential chirp is the integral of the frequency:

Where is the initial phase (at ).

The corresponding time-domain function for a sinusoidal exponential chirp is the sine of the phase in radians:

As was the case for the Linear Chirp, the instantaneous frequency of the Exponential Chirp consists of the fundamental frequency accompanied by additional harmonics.


A chirp signal can be generated with analog circuitry via a voltage-controlled oscillator (VCO), and a linearly or exponentially ramping control voltage. It can also be generated digitally by a digital signal processor (DSP) and digital to analog converter (DAC), using a direct digital synthesizer (DDS) and by varying the step in the numerically controlled oscillator. It can also be generated by a YIG oscillator.

Relation to an impulse signal

Chirp and impulse signals and their (selected) spectral components. On the bottom given four monochromatic components, sine waves of different frequency. The red line in the waves give the relative phase shift to the other sine waves, originating from the chirp characteristic. The animation removes the phase shift step by step (like with matched filtering), resulting in a sinc pulse when no relative phase shift is left.

A chirp signal shares the same spectral content with an impulse signal. However, unlike in the impulse signal, spectral components of the chirp signal have different phases,[4][5][6] i.e., their power spectra are alike but the phase spectra are distinct. Dispersion of a signal propagation medium may result in unintentional conversion of impulse signals into chirps. On the other hand, many practical applications, such as chirped pulse amplifiers or echolocation systems,[6] use chirp signals instead of impulses because of their inherently lower PAPR.

Uses and occurrences

Chirp modulation

Chirp modulation, or linear frequency modulation for digital communication, was patented by Sidney Darlington in 1954 with significant later work performed by Winkler in 1962. This type of modulation employs sinusoidal waveforms whose instantaneous frequency increases or decreases linearly over time. These waveforms are commonly referred to as linear chirps or simply chirps.

Hence the rate at which their frequency changes is called the chirp rate. In binary chirp modulation, binary data is transmitted by mapping the bits into chirps of opposite chirp rates. For instance, over one bit period "1" is assigned a chirp with positive rate a and "0" a chirp with negative rate −a. Chirps have been heavily used in radar applications and as a result advanced sources for transmission and matched filters for reception of linear chirps are available.

(a) In image processing, direct periodicity seldom occurs, but, rather, periodicity-in-perspective is encountered. (b) Repeating structures like the alternating dark space inside the windows, and light space of the white concrete, "chirp" (increase in frequency) towards the right. (c) Thus the best fit chirp for image processing is often a projective chirp.

Chirplet transform

Main article: Chirplet transform

Another kind of chirp is the projective chirp, of the form:


having the three parameters a (scale), b (translation), and c (chirpiness). The projective chirp is ideally suited to image processing, and forms the basis for the projective chirplet transform.[2]

Key chirp

A change in frequency of Morse code from the desired frequency, due to poor stability in the RF oscillator, is known as chirp,[7] and in the RST code is given an appended letter 'C'.

See also

Wikimedia Commons has media related to Chirp.


  1. "'Chirpyness': the rate of change of the instantaneous frequency."[2]


  1. Weisstein, Eric W. "Sweep Signal". From MathWorld--A Wolfram Web Resource.
  2. 1 2 Mann, Steve and Haykin, Simon; The Chirplet Transform: A generalization of Gabor's Logon Transform; Vision Interface '91.
  3. Easton, R.L. (2010). Fourier Methods in Imaging. Wiley. p. 703. ISBN 9781119991861. Retrieved 2014-12-03.
  4. "Chirped pulses". Retrieved 2014-12-03.
  5. Easton, R.L. (2010). Fourier Methods in Imaging. Wiley. p. 700. ISBN 9781119991861. Retrieved 2014-12-03.
  6. 1 2 "Chirp Signals". Retrieved 2014-12-03.
  7. The Beginner's Handbook of Amateur Radio By Clay Laster
Look up chirp in Wiktionary, the free dictionary.
This article is issued from Wikipedia - version of the 11/3/2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.