Brushless DC electric motor
Brushless DC electric motor (BLDC motors, BL motors) also known as electronically commutated motors (ECMs, EC motors) are synchronous motors that are powered by a DC electric source via an integrated inverter/switching power supply, which produces an AC electric signal to drive the motor. In this context, AC, alternating current, does not imply a sinusoidal waveform, but rather a bi-directional current with no restriction on waveform. Additional sensors and electronics control the inverter output amplitude and waveform (and therefore percent of DC bus usage/efficiency) and frequency (i.e. rotor speed).
Brushless motors may be described as stepper motors; however, the term "stepper motor" tends to be used for motors that are designed specifically to be operated in a mode where they are frequently stopped with the rotor in a defined angular position. This page describes more general brushless motor principles, though there is overlap.
Two key performance parameters of brushless DC motors are the motor constants Kv and Km.
Brushless vs. brushed motors
Brushed DC motors have been around since the mid-19th century, but brushless motors are a fairly recent arrival; a first step in the 1960s thanks to advances in solid state technology, with further improvements in the 1980s thanks to better permanent magnet materials.
Brushed DC motors develop a maximum torque when stationary, linearly decreasing as velocity increases. Some limitations of brushed motors can be overcome by brushless motors; they include higher efficiency and a lower susceptibility to mechanical wear. These benefits come at the cost of potentially less rugged, more complex, and more expensive control electronics.
A typical brushless motor has permanent magnets which rotate around a fixed armature, eliminating problems associated with connecting current to the moving armature. An electronic controller replaces the brush/commutator assembly of the brushed DC motor, which continually switches the phase to the windings to keep the motor turning. The controller performs similar timed power distribution by using a solid-state circuit rather than the brush/commutator system.
Brushless motors offer several advantages over brushed DC motors, including high torque to weight ratio, more torque per watt (increased efficiency), increased reliability, reduced noise, longer lifetime (no brush and commutator erosion), elimination of ionizing sparks from the commutator, and overall reduction of electromagnetic interference (EMI). With no windings on the rotor, they are not subjected to centrifugal forces, and because the windings are supported by the housing, they can be cooled by conduction, requiring no airflow inside the motor for cooling. This in turn means that the motor's internals can be entirely enclosed and protected from dirt or other foreign matter.
Brushless motor commutation can be implemented in software using a microcontroller or microprocessor computer, or may alternatively be implemented in analogue hardware, or in digital firmware using an FPGA. Commutation with electronics instead of brushes allows for greater flexibility and capabilities not available with brushed DC motors, including speed limiting, "micro stepped" operation for slow and/or fine motion control, and a holding torque when stationary. Controller software can be customized to the specific motor being used in the application, resulting in greater commutation efficiency.
When converting electricity into mechanical power, brushless motors are more efficient than brushed motors. This improvement is largely due to the frequency at which the electricity is switched determined by the position sensor feedback. Additional gains are due to the absence of brushes, which reduces mechanical energy loss due to friction. The enhanced efficiency is greatest in the no-load and low-load region of the motor's performance curve. Under high mechanical loads, brushless motors and high-quality brushed motors are comparable in efficiency.
Environments and requirements in which manufacturers use brushless-type DC motors include maintenance-free operation, high speeds, and operation where sparking is hazardous (i.e. explosive environments) or could affect electronically sensitive equipment.
Because the controller implements the traditional brushes functionality it needs the rotor's orientation/position (relative to the stator coils). This is automatic in a brushed motor due to the fixed geometry of rotor shaft and brushes. Some designs use Hall effect sensors or a rotary encoder to directly measure the rotor's position. Others measure the back-EMF in the undriven coils to infer the rotor position, eliminating the need for separate Hall effect sensors, and therefore are often called sensorless controllers.
In a brushless DC motor, two coils are energized at a time with equal and opposite polarities: one pushes the rotor away from it while the other attracts the rotor towards it. This increases the overall torque capacity of the motor and Hall effect sensors or a rotary encoder determine which two coils have to be energized to achieve this strategy.
A typical controller contains 3 bi-directional outputs (i.e., frequency controlled three phase output), which are controlled by a logic circuit. Simple controllers employ comparators to determine when the output phase should be advanced, while more advanced controllers employ a microcontroller to manage acceleration, control speed and fine-tune efficiency.
Controllers that sense rotor position based on back-EMF have extra challenges in initiating motion because no back-EMF is produced when the rotor is stationary. This is usually accomplished by beginning rotation from an arbitrary phase, and then skipping to the correct phase if it is found to be wrong. This can cause the motor to run briefly backwards, adding even more complexity to the startup sequence. Other sensorless controllers are capable of measuring winding saturation caused by the position of the magnets to infer the rotor position.
Variations in construction
Brushless motors can be constructed in several different physical configurations: In the 'conventional' (also known as inrunner) configuration, the permanent magnets are part of the rotor. Three stator windings surround the rotor. In the outrunner (or external-rotor) configuration, the radial-relationship between the coils and magnets is reversed; the stator coils form the center (core) of the motor, while the permanent magnets spin within an overhanging rotor which surrounds the core. The flat or axial flux type, used where there are space or shape limitations, uses stator and rotor plates, mounted face to face. Outrunners typically have more poles, set up in triplets to maintain the three groups of windings, and have a higher torque at low RPMs. In all brushless motors, the coils are stationary.
There are two common electrical winding configurations; the delta configuration connects three windings to each other (series circuits) in a triangle-like circuit, and power is applied at each of the connections. The Wye (Y-shaped) configuration, sometimes called a star winding, connects all of the windings to a central point (parallel circuits) and power is applied to the remaining end of each winding.
A motor with windings in delta configuration gives low torque at low speed, but can give higher top speed. Wye configuration gives high torque at low speed, but not as high top speed.
Although efficiency is greatly affected by the motor's construction, the Wye winding is normally more efficient. In delta-connected windings, half voltage is applied across the windings adjacent to the driven lead (compared to the winding directly between the driven leads), increasing resistive losses. In addition, windings can allow high-frequency parasitic electrical currents to circulate entirely within the motor. A Wye-connected winding does not contain a closed loop in which parasitic currents can flow, preventing such losses.
From a controller standpoint, the two styles of windings are treated exactly the same.
Brushless motors fulfill many functions originally performed by brushed DC motors, but cost and control complexity prevents brushless motors from replacing brushed motors completely in the lowest-cost areas. Nevertheless, brushless motors have come to dominate many applications, particularly devices such as computer hard drives and CD/DVD players. Small cooling fans in electronic equipment are powered exclusively by brushless motors. They can be found in cordless power tools where the increased efficiency of the motor leads to longer periods of use before the battery needs to be charged. Low speed, low power brushless motors are used in direct-drive turntables for gramophone records.
A number of electric bicycles use brushless motors that are sometimes built into the wheel hub itself, with the stator fixed solidly to the axle and the magnets attached to and rotating with the wheel.
Heating and ventilation
There is a trend in the HVAC and refrigeration industries to use brushless motors instead of various types of AC motors. The most significant reason to switch to a brushless motor is the dramatic reduction in power required to operate them versus a typical AC motor. While shaded-pole and permanent split capacitor motors once dominated as the motor of fan, many fans are now run using a brushless motor. Some fans use brushless motors also in order to increase overall system efficiency.
In addition to the brushless motor's higher efficiency, in HVAC systems (especially those featuring variable-speed and/or load modulation) use brushless motors because the built-in microprocessor allows for programmability, control over airflow, and serial communication. Some ceiling fan and portable fans are also featuring this motor. They advertise the motor being highly energy efficient and quieter than most fans.
The application of brushless DC motors within industrial engineering primarily focuses on manufacturing engineering or industrial automation design. In manufacturing, brushless motors are primarily used for motion control, positioning or actuation systems.
Brushless motors are ideally suited for manufacturing applications because of their high power density, good speed-torque characteristics, high efficiency, wide speed ranges and low maintenance. The most common uses of brushless DC motors in industrial engineering are linear motors, servomotors, actuators for industrial robots, extruder drive motors and feed drives for CNC machine tools.
Motion control systems
Brushless motors are commonly used as pump, fan and spindle drives in adjustable or variable speed applications. They can develop high torque with good speed response. In addition, they can be easily automated for remote control. Due to their construction, they have good thermal characteristics and high energy efficiency. To obtain a variable speed response, brushless motors operate in an electromechanical system that includes an electronic motor controller and a rotor position feedback sensor.
Brushless DC motors are widely used as servomotors for machine tool servo drives. Servomotors are used for mechanical displacement, positioning or precision motion control. In the past DC stepper motors were used as servomotors; however, since they are operated with open loop control, they typically exhibit torque pulsations. Brushless dc motors are more suitable as servomotors since their precise motion is based upon a closed loop control system that provides tightly controlled and stable operation.
Positioning and actuation systems
Brushless motors are used in industrial positioning and actuation applications. For assembly robots, brushless stepper or servo motors are used to position a part for assembly or a tool for a manufacturing process, such as welding or painting. Brushless motors can also be used to drive linear actuators
Motors that directly produce linear motion are called linear motors. The advantage of linear motors is that they can produce linear motion without the need of a transmission system, such as a ball-and-lead screw, rack-and-pinion, cam, gears or belts, that would be necessary for rotary motors. Transmission systems are known to introduce less responsiveness and reduced accuracy. Direct drive, brushless DC linear motors consist of a slotted stator with magnetic teeth and a moving actuator, which has permanent magnets and coil windings. To obtain linear motion, a motor controller excites the coil windings in the actuator causing an interaction of the magnetic fields resulting in linear motion. Tubular linear motors are another form of linear motor design operated in a similar way.
Brushless motors are a popular motor choice for model aircraft including helicopters. Their favorable power-to-weight ratios and large range of available sizes, from under 5 gram to large motors rated at well into the kilowatt output range, have revolutionized the market for electric-powered model flight, displacing virtually all brushed electric motors. They have also encouraged a growth of simple, lightweight electric model aircraft, rather than the previous internal combustion engines powering larger and heavier models. The large power-to-weight ratio of modern batteries and brushless motors allows models to ascend vertically, rather than climb gradually. The low noise and lack of mass compared to small glow fuel internal combustion engines is another reason for their popularity.
Legal restrictions for the use of combustion engine driven model aircraft in some countries, most often due to potential for noise pollution — even with purpose-designed mufflers for almost all model engines being available over the most recent decades — have also supported the shift to high-power electric systems.
Their popularity has also risen in the radio-controlled (RC) car area. Brushless motors have been legal in North American RC car racing in accordance to ROAR since 2006. These motors provide a great amount of power to RC racers and, if paired with appropriate gearing and high-discharge Li-Po (lithium polymer) or safer (but heavier and less powerful) LiFePO4 batteries, these cars can achieve speeds over 100 miles per hour (160 km/h).
Brushless motors are capable of producing more torque and have a faster peak rotational speed compared to nitro- or gasoline-powered engines. Nitro engines climax to peak at around 46,800 RPM and 2.95HP, while a smaller brushless motor has instantaneous maximum torque at start, and, when tapering off, can reach 50,000 RPM and 5HP. Larger brushless RC motors can reach upwards of 14 hp and 28,000 RPM to power 1/5th scale models.
- T.G. Wilson, P.H. Trickey, "D.C. Machine. With Solid State Commutation", AIEE paper I. CP62-1372, October 7, 1962
- M. Gopal. Control systems: principles and design. 2nd ed. Tata McGraw-Hill, 2002. Page 165.
- Curie temperature
- "Brushless DC motor design", retrieved on April 26, 2015.
- ECMs and HVAC Systems
- Ohio Electric Motors. Brushless DC Motors Used in Industrial Applications. Ohio Electric Motors. 2012. Archived November 8, 2012, at WebCite
- Ohio Electric Motors. DC Motor Protection. Ohio Electric Motors. 2011. Archived November 28, 2011, at WebCite
- Sabrie Soloman. Sensors handbook. 3rd ed. McGraw-Hill, 1999. Page 5-6.
- Pter Campbel. Permanent Magnet Materials and their Application. Cambridge University Press, 1996. Page 172.
- M. Gopal. Control systems: principles and design. 2nd ed. Tata McGraw-Hill, 2002. Page 159.
- Shimon Y. Nof, Wilbert E. Wilhelm and Hans-Jürgen Warnecke. Industrial assembly. Springer, 1997. Page 174.
- Peng Zhang. Industrial Control Technology: A Handbook for Engineers and Researchers. William Andrew, Inc., 2008. Page 91.
- Ohio Electric Motors. Brushless DC Motors Used in Industrial Applications. Ohio Electric Motors. 2012. 1Archived November 8, 2012, at WebCite
- Bernstein, Bobby (15 January 2015). "Top 4 Fastest RC Cars for Sale in the World". heavy.com. Retrieved 2 February 2015.
As far as THE fastest RC car available for sale is concerned, it is the Traxxas XO-1 Supercar. The XO-1 hits 100mph, with proper LiPos batteries.The maker's product specs indicates the usage of a "Traxxas Big Block brushless motor"
|Wikimedia Commons has media related to Brushless DC electric motors.|
- How Motors Work (brushed and brushless RC airplane motors)
- Animation of BLDC Motor in different commutation (Block, Star, Sinus (sine) & Sensorless) - compared to stepper motors. Flash
- RC Hobby Mysteries: What is Brushless Motor
- Electric Drives - Brushless DC / AC and Reluctance Motors with useful diagrams