An articulated bus (either a motor bus or trolleybus) is an articulated vehicle used in public transportation. It is usually a single-deck design, and comprises two rigid sections linked by a pivoting joint (articulation) enclosed by protective folding bellows on the in- and outside of the vehicle (usually of gray or black colour) and a cover plate on the inside of the vehicle. This arrangement allows a longer legal overall length than single-decker rigid-bodied buses, and hence a higher passenger capacity, while still allowing the bus to maneuver adequately on the roads of its service route.
Around the English-speaking world, articulated buses have acquired several different synonyms that allude to their articulated design, such as bendy buses, bending buses, tandem buses, stretch buses, double buses, banana buses, slinky buses, wiggle buses, caterpillar buses, accordion buses or vestibule buses . Due to their high passenger capacity, articulated buses are often used as part of bus rapid transit schemes, and can include mechanical guidance.
Used almost exclusively on public transport bus services, articulated buses are approximately 18 metres (59 ft) in length; standard rigid-construction buses are usually 11 to 14 metres (36 to 46 ft). The common arrangement of an articulated bus is to have a forward section with two axles leading a rear section with a single axle, with the driving axle mounted on either the front or the rear section. Some articulated bus models have a steering arrangement on the rearmost axle which turns slightly in opposition to the front steering axle, allowing the vehicle to negotiate turns in a crab-like fashion, similar to hook-and-ladder fire trucks operating in city environments. A less common variant of the articulated bus is the bi-articulated bus, where the vehicle has two trailer sections rather than one. Their capacity is around 200 people, and their length about 25 metres (82 ft).
Early examples of the articulated bus appeared in Europe in the 1920s. In Budapest, the first prototype of this bus was in service in 1960 and could carry 200 passengers. It was manufactured without the use of blueprints. Later Ikarus's blueprints were drawn up on the basis of this existing prototype. There is an ongoing exhibition in Budapest at the Museum of Transportation in 2010 with the title "The articulated bus is 50 years old".
In the mid-1960s, AC Transit in California pioneered the American use of a modern articulated bus, operating the experimental commuter coach "XMC 77" (based on Continental Trailways' Bus & Car Co. Silver Eagle model) on some of its transbay lines. Articulated buses have also been used in Australia and Europe (Austria (Gräf & Stift), Italy, Germany(Gaubschat, Emmelmann, Göppel, Duewag, Vetter), Canada (LFS Articulated), Hungary (Ikarus), Poland (Jelcz AP02)) The first modern British "bendy buses" (as they are referred to in the UK and Canada) were built by Leyland-DAB and used in the city of Sheffield in the 1980s. They were subsequently withdrawn from service because they proved to be expensive to maintain.
Advantages and disadvantages
The main benefits of an articulated bus over the double-decker bus are rapid simultaneous boarding and disembarkation through more and larger doors, much larger passenger capacity (120+ versus 80−90), increased stability arising from a lower centre of gravity, smaller frontal area giving less air resistance than double decker buses thus better fuel efficiency, often a smaller turning radius, higher maximum service speed, and improved accessibility for people with disabilities and the elderly.
One disadvantage that is sometimes experienced with some articulated models is the insufficiency of the effective motive power available to them. It is common for articulated buses to use the same engine type as non-articulated buses (for example, the Hungarian Ikarus 260 solo and IK 280 bendy share a common 10,350 cubic centimetres (631.6 cu in), 192 brake horsepower (143 kW; 195 PS) inline six diesel engine). The extra weight of the bendy bus gives rise to a slower speed and acceleration. When used in cities built on numerous inclines (e.g. Vancouver, B.C. or San Francisco, California) the vehicle is prone to overheating. This may lead to stalling, or in the worst situations to an outbreak of fire if the bus is powered by a diesel engine. During late 2003 and early 2004, a series of onboard fires on newly delivered Mercedes-Benz Citaros led to Londoners humorously nicknaming the vehicles chariots of fire. Mercedes-Benz quickly addressed the problem, although the vehicles were out of service for a period. However, no overheating or fire-related incidents have ever been recorded in Vancouver's articulated electric trolley buses from a similar cause. Vancouver's articulated trolley buses were specifically chosen for the higher torque output of their electric motors, which typically outperform diesel-based low-floor buses.
In some circumstances of urban operation (such as in areas with narrow streets and tight turns), articulated buses may also be involved in significantly more accidents than conventional buses. Estimates for London's articulated buses put their involvement in accidents involving pedestrians at over five times the rate of all other buses, and over twice as high for accidents involving cyclists. In a period when articulated buses made up approximately 5% of the London bus fleet, they were involved in 20% of all bus-related deaths, statistics which eventually led to their replacement. However, these safety statistics may be partly skewed due to the buses having been used on the busiest routes in the most crowded areas of the city, making them look worse than the buses they were being compared with.
Articulated buses have been used in most European countries for many years. Until 1980, they were illegal on the UK's roads. A 1979 experiment by South Yorkshire Passenger Transport Executive with buses manufactured by MAN and Leyland-DAB led to a change in the law, but the experiment was abandoned in 1981 because double-decker buses were generally considered less expensive both to purchase and to operate. The cost and weight of the strengthened deck framing and staircase of a double-decker was lower than the cost and weight of the additional axle(s) and coupling mechanism of an articulated bus. Modern technology has reduced the weight disadvantage, and the benefits of a continuous low floor allowing easier access plus additional entrance doors for smoother loading have led to reconsideration of the use of articulated buses in the UK.
Articulated buses became popular in mainland Europe due to their increased capacity compared with regular buses. In many cities, lower railway bridge clearances have precluded the use of double-deck vehicles, which have never achieved great popularity there. Overhead wires for trams, trolleybuses etc. are not really relevant issues, as the minimum normal clearance above road level is standard across the EU and is well in excess of the height of a double-deck vehicle. (Otherwise many freight vehicles would encounter severe problems in the course of normal operation.)
In London, articulated buses were used on some routes from 2001 until 2011, but they were not a success. Boris Johnson, former Mayor of London, promised in the run-up to the mayoral election of 2008 to rid the city of the controversial buses and replaced them with double deckers.
Elsewhere in the UK, they are generally operated on particular routes in order to increase passenger numbers, rather than across entire networks. With unsupervised “open boarding” through three doors and the requirement for pre-purchase of tickets, levels of fare-dodging on the new vehicles were found to be at least three times higher than on conventional buses where entry of passengers is monitored by the driver or conductor. The only way of checking for free riders was to use large teams of ticket inspectors to swamp the bus and inspect all tickets while keeping the doors closed, meanwhile delaying the further progress of the bus. Since the articulated buses were tending to serve areas of relative deprivation it is suspected that this was a contributory factor in Transport for London (TfL) turning against the concept.
In Israel, the use of articulated buses – commonly called long buses – is widespread, particularly in Gush Dan and Jerusalem, the two great urban centers of the country. The long buses are considered reliable and useful, and have been in service in Israel since the mid-1970s. During the Israeli-Palestinian conflict, such buses were often targeted by Palestinian terrorists and suicide bombers during rush hours, since a crowded long bus can contain more than 100 passengers. Due to the al-Aqsa Intifada wave of mass bombings, security measures were enforced and today many long buses in Israel are accompanied by a security guard.
An articulated bus is a long vehicle and usually requires a specially trained driver, as maneuvering (particularly reversing) can be difficult. Articulated electric trolleybuses can be difficult to control, with their motors producing momentary peak power in excess of 600 kilowatts (816 PS; 805 hp). The trailer section of a "puller" bus can be subject to unusual centripetal forces, which many people can find uncomfortable, although this is not an issue with "pushers". Nonetheless, the articulated bus is highly successful in Budapest, Hungary, where the BKV city transit company has been operating more than 1000 of them every day since the early 1970s. The Hungarian company Volán also runs hundreds of articulated buses on intercity lines.
Articulated buses are commonplace in such US urban centers as Akron, Baltimore, Boston, Cleveland, Minneapolis-St.Paul, Miami, Orlando, Chicago, Denver, Houston, Indianapolis, Los Angeles, New York City, Orange County (California), Pittsburgh, Philadelphia, Phoenix, the Quad Cities, Rochester, San Diego, San Francisco, Seattle, and Washington, D.C.. In Eugene, Lane Transit District uses articulated buses on some high-traffic routes, as well as on their Emerald Express (EmX) Bus Rapid Transit Service.
In Canada, they are used in Brampton, Calgary, Edmonton for the routes 8, 9, and 33, Halifax, Hamilton, London, Longueuil, Mississauga, Toronto, Montreal, Ottawa, Quebec City, Saskatoon, Winnipeg, York Region and Vancouver.
In Asia, many major Chinese cities had fleets of articulated buses prior to the late 1990s. Some of these fleets have since been replaced by single-section units except in a few cities, namely Beijing, Shanghai, and Hangzhou. While in the 2000s a surge in BRT construction has reintroduced or re-purposed the articulated bus fleets for rapid transit usage in cities like Changzhou, Dalian, Guangzhou, Jinan, Kunming, Xiamen, Yancheng, Zaozhuang, and Zhengzhou. In South America, they are used in São Paulo, Curitiba, Santiago and Bogotá.
In Adelaide, Australia, articulated buses are used on the O-Bahn guided busway, reaching speeds of 100 km/h. The first articulated buses to use it were the Mercedes-Benz O305G buses; however, three MAN SG280H buses are also equipped for O-Bahn use. In recent years, it has proven problematic to find suitable low-floor articulated buses to replace the 1984-manufactured Mercedes buses, because the design of the O-Bahn track unfortunately precludes the use of most modern articulated buses. Sydney, Australia has seen the operation of articulated buses for many years. Currently it operates a fleet of various models with eighty Volvo B12BLEA buses joining the Sydney Buses fleet in 2005 and 2006, increasing capacity along many of the busy corridors. A number of prototype vehicles were delivered in 2008 & 2009 to operate on Sydney Buses' first Metrobus route, the M10 from Leichhardt to Kingsford and Maroubra Junction. The buses feature different chassis, body types, and internal layouts. The articulated Volvo B12BLEA buses are fully wheelchair-accessible, air-conditioned, and have visual and audible next-stop passenger information systems installed. The buses feature air-conditioning, large electronic destination displays and cloth seating. Additionally, each bus features a stepless entry, which will assist less-mobile passengers. Flip-up seats in the front part of the bus allow easy accommodation for passengers in wheelchairs and with strollers and prams. In 2009-2010 150 new Volvo B12BLEA articulated buses have been introduced into the Sydney Buses fleet, many of these part of the expanded Metrobus program.
In Singapore, articulated buses were first introduced in 1996 by Trans-Island Bus Services (now SMRT Buses) with the Mercedes-Benz O405G buses (bodied in Hispano Carrcera (MK1/MK2), Hispano Habit and Volgren CR221L). They were given the moniker "bendy buses", a name which is still in use today. In April of that year, SBS Transit introduced a demonstrator Volvo B10MA bus (registration SBS998Y) fitted with a three-door version of the Duple Metsec bodywork similar to that of Volvo's B10M buses. With a length of 19 metres (62 ft), this bus earned the title of "Asia's Longest Bus". In 1997, SBS Transit purchased another bendy bus, the Mercedes-Benz O405GN (registration SBS999U), again as a demonstrator. This bus had Volgren CR221L bodywork. In March 2006, SBS Transit sold all its bendy buses to New Zealand after encountering drivability issues with the Volvo B10MA bus and air-conditioning problems with the Mercedes-Benz bus, and also deciding that double-decker buses could carry more passengers while taking up less road space, as opposed to SMRT's stance that "articulated buses offer greater accessibility and efficiency".
From 3 July 2011 to 28 August 2013, articulated Mercedes Citaro buses purchased from London have been used in Malta by the company Arriva on a number of routes across the country. A number of serious engine fires resulted in their withdrawal from service, and they have also been responsible for causing an increase in traffic congestion and accidents involving pedestrians and cyclists.
Man Castrosua Bendy Bus
Viva Transit Van Hool AG300
New Flyer DE60LFR in Waipahu, Honolulu, Hawaii
Crown-Ikarus in Portland, Oregon
Articulated buses can be of "pusher" or "puller" configuration. In most puller articulated buses, the engine is mounted under the floor between the front and middle axles, and only the middle axle is powered. Some consider this an outdated design, as it prohibits floor levels lower than approximately 750 millimetres (30 in), and can produce passenger discomfort due to high noise and vibration levels. On the other hand, the puller bus is cheaper to manufacture, and can be used in very narrow or severely potholed streets. This type of bus also performs better in snowy or icy conditions, as the thrust from the driving wheels does not cause the vehicle to jacknife. Newer models such as the Van Hool AG300 feature low floor while maintaining the puller design placing the engine block off-center opposite to the second door. Also, the unpowered rear axle is much simpler and carries no engine weight, facilitating the installation of counter-steering mechanisms to further decrease the turning radius.
In pusher buses, only the rear axle is powered by a rear-mounted internal combustion engine, and the longitudinal stability of the vehicle is maintained by active hydraulics mounted under the turntable. This modern system makes it possible to build buses without steps and having low floors along their entire length, which simplifies access for passengers with limited mobility.
Modern low-floor pusher articulated buses also tend to suffer from suspension problems because their wheels lack the ampleness of travel that would enable them to absorb surface unevennesses. This also leads to passenger discomfort and relatively rapid disintegration of the vehicle's superstructure.
Although the majority of articulated buses utilise diesel engines for their motive power, a number of operators (primarily outside of North America and by LACMTA) are adopting compressed natural gas (CNG) power in order to reduce pollution. Many other transit authorities in the United States and Canada are adopting articulated buses that are diesel-electric hybrids, such as the New Flyer DE60LF. There are also articulated trolleybuses (electric).
A typical puller model is the Hungarian-made Ikarus 280, the articulated version of the Ikarus 260, of which 60.993 buses were manufactured between 1973 and 2002, mostly for Soviet bloc customers. (In the '70-s this type gave the 2/3 of the World's articulated bus building.) Makers of pusher-type articulated buses include Mercedes-Benz, New Flyer Industries, MAN, Volvo and Scania. Puller-type articulated buses are built in less numbers, but are still available in Scandinavia and South America. Examples being the Volvo B9S and Volvo B12M. The Renault PR 180 and PR 180.2 (articulated versions of the PR 100 and PR 100.2) were a special variation of the pusher design in which both the middle and axles were driven, with a driveshaft passing through the turntable between the two driving axles. Very few companies specialise in manufacturing the articulated section for the buses. One that does is ATG Autotechnik GmbH in Siek near Hamburg.
Since the late 1980s, the concept of the articulated bus has been extended further with the addition of a second trailer section that extends the bus almost to tram length and capacity, to create a bi-articulated bus, called also triple bus. The Chinese manufacturer Zhejiang Youngman (Jinhua Neoplan) has developed the 25 metres (82 ft) JNP6280G bi-articulated bus, deemed the "world's largest", which will be used in Beijing.
Bi-articulated buses are still rare, having been trialled and rejected in some places. Because of their length they have a role on very high-capacity routes, or as a component of a bus rapid transit scheme. Major examples of bi-articulated buses playing a major role in bus rapid transit can be found in Curitiba, Bogota, Mexico City, Santiago de Chile, etc. Volvo is a major supplier of puller-type bi-articulated buses in these markets. In the Netherlands, bi-articulated buses came into service in Utrecht (2002) and Groningen (2014) on busy routes.
Double-decker articulated buses
A few attempts have been made to design a double-decker articulated bus. NEOPLAN Bus GmbH built a handful of Neoplan Jumbocruisers between 1975 and 1992. In these models, only the upper deck allows movement between the two sections, so each section has its own doors and set of stairs.
In some countries of the European Union, as well as in the United States and Canada, an articulated bus can be driven with the same license used to drive a rigid bus (D in Europe), while a bus towing a normal trailer requires a bus + trailer (D+E) license. However, special training is needed for bi-articulated buses.
In popular culture
In a campaign associated with the Transformers: Revenge of the Fallen film, a 2014 Transformers character was created using parts from an articulated bus with the actual vehicle as its intended alternate form and dubbed "Bendy-Bus Prime."
|Wikimedia Commons has media related to Articulated buses.|
- "Articulated Transit Bus Steering Considerations". North American Bus Industries. Archived from the original on 13 November 2006. Retrieved 7 January 2007.
- Photo of AC Transit XMC 77 at the Transbay Terminal in San Francisco, California, circa 1965 Archived 23 August 2011 at the Wayback Machine.
- "Bendy-buses withdrawn after fires". BBC. BBC News. 24 March 2004. Retrieved 7 January 2007.
- Johnson ditches London's bendy buses
- Bendy buses - the fatal facts Archived 22 April 2008 at the Wayback Machine.
- The Bendy Bus: A Transport Revolution Ingenia Magazine, March 2005
- fotopic.net, Desmond Tay, 27 January 2009. Retrieved 2009-11-13.
- Bendy buses given boot over fire fears, Times of Malta, 28 August 2013. Retrieved 2015-12-06.